home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Cream of the Crop 20
/
Cream of the Crop 20 (Terry Blount) (1996).iso
/
bbs
/
tg_302.zip
/
INSTALL.DOC
< prev
next >
Wrap
Text File
|
1996-07-14
|
15KB
|
315 lines
Telegard Bulletin Board Software, v3.02
Installation Documentation
Copyright (C) 1995,1996 by Tim Strike
All Rights Reserved.
INTRODUCTION
Welcome to Telegard Bulletin Board Software, version 3.02. This
documentation contains quick instructions for installing Telegard
for the first time, or for completing an upgrade from previous
versions of the Telegard software.
Please read README.DOC before continuing with this installation.
Please read these instructions very carefully. The steps we have
outlined are designed to ensure that you install our system with
minimal effort and with success the FIRST time!
If you are upgrading from a previous version of Telegard, you should
refer to the section titled "UPGRADE INSTRUCTIONS", otherwise if you
are a first time user of Telegard, please follow the "NEW
INSTALLATION" section.
SYSTEM REQUIREMENTS
Memory 440K minimum
Diskspace, installation 2 megs
post-installation 1 meg + messages + files + doors + data
recommended 10+ megs at least
Fossil Driver (level 5)
Share/OS-equivalent (for multinode)
PKZIP VERSION NOTES
Our package is released with PKZIP version 2.04g. This is the
latest publically available version of PKZIP as of June 29, 1996.
There are several hacked versions of PKZIP 1.10 going around which
have versions in the 3.nn and 4.nn series of numbers. PKZIP 1.10
and subsequently these hacked versions, are *not* compatible with
the encryption method used in 2.04g and in the file INSTALL.TG.
NEW INSTALLATION
1) Create a new directory for your Telegard BBS
2) Copy INSTALL.TG into the new directory
3) Type "PKUNZIP INSTALL.TG -sONLYRAINS" at the DOS command prompt,
without the quotes. This will extract the necessary install
files for your system.
4) Type "TELEGARD" at the DOS command prompt, without the quotes.
This will start the installation process. We will ask you a few
simple questions regarding the placement of the remaining data
files. You should configure these directories in such a manner
that the directory structure is not obvious (i.e. do not use
/DATA/ as your data directory).
5) The installation process will build the desired directory
structure, unpack the enclosed data files, and create any other
data files which are needed for BBS installation.
6) Run "INDEX BUILD ALL" from the main /bbs/ directory to create
the index files as required by the system.
7) From your main bbs directory run "MAKELANG .\LANGUAGE\ENGLISH"
to compile your new language file (Note: Replace \LANGUAGE\ with
your correct language path).
8) Run "TELEGARD -?" to familiarize yourself with the commands
available from the command line.
9) Run "TELEGARD -L" to load the BBS locally -- Hit "ESC" for the
menu commands available -- Use the System Configuration and
System Manager commands to setup the remainder of your BBS
system (remember to change the information in the first user
record to your OWN personal information!).
10) You may delete INSTALL.TG and *.TWS after the installation has
been completed. These files are only temporary installation
files and are not used in the general operation of the BBS. You
should save a copy of the original archive (TG_nnn@n.ZIP) in
case you want or need to reinstall the software at a later date.
You can also delete the UPGRADE.EXE file, which is only used if
upgrading from a previous gamma of Telegard.
11) Remember to read RELEASE.DOC at some point in the near future.
UPGRADING INSTRUCTIONS
If you are upgrading from Telegard 2.7, please refer to the section
immediately following this text. If you are upgrading from a
gamma release of Telegard 3.0, please skip to the section for gamma
upgrades.
TELEGARD 2.7 UPGRADING INSTRUCTIONS
The differences between Telegard 2.7 and Telegard 3.0 are quite
profound. We suggest that you take the upgrade slowly and tackle
it over a couple of days to ensure that you get the upgrade right
before putting your new 3.0 system online.
To successfully upgrade from 2.7 to 3.0, you will need the archive
"TG_UPG32.ZIP", distributed at the same time that Telegard 3.0 was
distributed. This file contains the upgrade program which is needed
to upgrade from Telegard 2.7.
Create a backup of your 2.7 BBS system. This will ensure you have
a downgrade path if necessary.
Telegard 3.0 should be placed in a new directory -- your old BBS
directory will no longer be used. This will mean that many of your
system files will have to point towards new directories, etc. This
is good for two reasons; firstly, it will ensure that you use
software which is only compatible with Telegard 3.0, and secondly;
it will ensure that your system security is preserved.
1) Create a new directory for your Telegard BBS
2) Copy INSTALL.TG into the new directory
3) Type "PKUNZIP INSTALL.TG -sONLYRAINS" at the DOS command prompt,
without the quotes. This will extract the necessary install
files for your system.
4) Type "TELEGARD" at the DOS command prompt, without the quotes.
This will start the installation process. We will ask you a few
simple questions regarding the placement of the remaining data
files. You should configure these directories in such a manner
that the directory structure is not obvious (i.e. do not use
/DATA/ as your data directory).
5) The installation process will build the desired directory
structure, unpack the enclosed data files, and create any other
data files which are needed for BBS installation.
6) Follow the remaining instructions as provided by the
installation process, except skip "INDEX ALL BUILD" for now.
7) You may delete INSTALL.TG and *.TWS after the installation has
been completed. These files are only temporary installation
files and are not used in the general operation of the BBS. You
should save a copy of the original archive (TG_nnn@n.ZIP) in
case you want or need to reinstall the software at a later date.
8) Copy the "TG_UPG32.ZIP" file into your new directory.
9) Type "PKUNZIP TG_UPG32.ZIP" at the DOS command prompt,
without the quotes. This will extract the necessary upgrade
files for your system.
10) Review UPGRADE.DOC to familiarize yourself with the upgrade
instructions.
11) Type "UPGRADE" at the DOS command prompt, without the quotes.
When prompted, input your Telegard 2.7 information and then
follow the remaining instructions for the upgrade.
12) Switch to your /data/ directory and type "REN CONFRENC.DAT
GROUPS.DAT".
13) Type "UPDATE" at the DOS command prompt, without the quotes.
When prompted, select Telegard 2.7 as your upgrade path, and
the program will do the remainder of the updates from G1 to
G4 (if using a version of TG_UPD later